1. Balance output equipment of new system
"INVERTED S BALANCE circuit" adoption
It is transmission system of the ideal to which
balance transmission cancels the noise which is induced in the
transmission cable, does not receive the influence of imported noise.
As for this balance output amplifier it is general to form with
the operational amplifier by IC, but when it is this method, it cannot
guarantee sufficient efficiency at such as the dynamic range and
Signal-noise ratio.
With DENON, in order to pull out without leaving the
characteristic of balance transmission system, developing the
INVERTED? leek ALANCE circuit anew. As amplifying element
everything is made discrete constitution of the high performance and
high quality part use, power supply voltage is converted approximately
3 times that of system (±47V) to high tension until recently, low,
with the distortion removal circuitry which furthermore develops DENON
individual non return technology, actualizing distortion factor and
high Signal-noise ratio. The sufficient dynamic range sharp
startup quality was guaranteed.
2. In output step in all FET type advanced flat
amplifier unbalanced output step of MOS FET adoption MOS FET adoption
As for FET, time lag of signal transmission being
little extremely, input impedance is very large, it meaning that the
odd number next distortion factor does not occur, it has ideal quality
as a transmission amplifying element of the analog signal. The
knitting machine, pursued, the ideal of the amplifier of digital age,
such as CD, DAT and BS formed the flat amplifier with FET.
As the first level the pole makes differential amplification of
noise FET low, goes hand in hand with refuse coat bootstrap system,
decreases the feedback between input/output to the extremity,
linearity was improved substantially. In addition, MOS FET
(Pc30W) the pre- driver step of adoption improves linearity
substantially the similar cascode bootstrap to the first level, with
P-P system, low assures the improvement straightening high pass
quality. MOS FET (Pc30W) the end step of adoption consists of
the source follower circuit, is compatible load drive quality with
high input impedance low, obtains the transmission characteristic
which is superior as a flat amplifier of digital age.
3. Balanced lance adoption of wide band LC-OFC coil
(CD-2 balance input)
Because it corresponds to the balance output which
is equipped in the high-class CD player et. al., balance input
transformer of the wide band LC-OFC coil was adopted for CD-2 balance
input. Because of this, quite being smooth unlike the
operational amplifier system due to IC, wide band you obtain quality.
4. The LC- p type power circuit which uses the
large-sized coil which cuts power source noise
In order to cut off power source noise, the
knitting machine adopted the LC- p type power circuit by the
large-sized choke coil.
5. The constant voltage power supply classified by
unit which removes mutual interference
The equalizer - pure electric current was supplied
to the amplifier, the flat amplifier, the balance amplifier and the
control circuit with shortest course, the constant voltage power
supply which removes the interference between each unit was loaded
classified by unit.
Advanced high quality PHONO equalizer of 6.MOS POWER FET
adoption and maximum permissible input 500mV/1kHz - amplifier
Up-to-date technology was thrown to also analog
disk playback, polishing was bet on degree of completion as a pre-amp.
As for the knitting machine, as the maximum permissible input
500mV/1kHz which corresponds to wide ??????????
playback is acquired, MOS POWER FET (Pc30W) you adopted for the output
step, assured the high acceleration of signal transmission, improved
load drive quality low.
7.PHONO input MM/MC 2 systematic equipment. In MC
input LC-OFC trance adoption
As for MC input, like the recent high-class MC
cartridge because it corresponds to the cartridge of very low power
output voltage, boosting ratio 1: MC trance of the LC-OFC coil
of 20 was adopted.
8. With "EQ OFF switch" equipment the equalizer -
amplifier complete separation (power source OFF) the design
When using PHONO input, the circuit and power
source were cut off completely the equalizer - by the amplifier OFF
switch, cancelled influence to such as CD playback.
9. The high performance it is low in the all stage
input circuits noise FET
10 Advanced balance input/output terminal,
RCA pin-jack adoption
The high accuracy 4 connected large-sized (40
types) of 11.L and R each 2 connected parallel uses volume
The high accuracy 4 connected large-sized (40
types) of L and R each 2 connected parallel uses volume is used to
main volume. Contact resistance of the resistor and the brush is
decreased, sound quality deterioration quite is made small.
12. Using ????? for the volume knob.
The Takasina rank due to real wood mirror surface finish cabinet
adoption design
????? is the lumber which has been used
for the pipe. In order the pipe while using over long time, to
keep adapting to the hand, when touching, ????? whose touch
is good was adopted for also the volume knob which long time is
handled. In addition, the cabinet the tastefulness due to
multilayer coding made the real wood mirror surface finish which
overflows, the Takasina rank which adopts the trap door collected with
design.
13 In addition merit
- Adopting copper plating to the high rigid chassis
and the front chassis of the sintered metal based large-sized weight
class foot and plank material use
- Adopting treble quality part such as high quality
resistant for sound and electrolytic condenser and film condenser
- Adopting the epoxy based glass compound baseplate
which in the printed circuit board is superior in strength, electric
efficiency and resistance swing characteristic
- Input change the electronic switch and the
software touch operation by advanced relay. The pre-setting
switch attaching which can appoint the input at the time of power
source ON
Specification standard
* Equalizer - amplifier section (PHONO IN - REC OUT)
- Input sensitivity/input impedance
- PHONO-MC 125 µ V/40 O
- PHONO-MM 2.5mV/47k O
- Maximum permissible input
- PHONO-MC 25mV/1kHz
- PHONO-MM 500mV/1kHz
- Installed capacity/rated output
- Total height harmonic wave distortion factor
- PHONO-MC - REC OUT 0.01% (10V/1kHz)
- PHONO-MM - REC OUT 0.005% (10V/20Hz - 20kHz)
- CD-1 - PRE OUT-1 0.005% (10V/20Hz - 20kHz)
- CD-2 - PRE OUT-2 0.005% (10V/1kHz)
- RIAA deviation
- PHONO-MC 30Hz - 20kHz ±0.3dB
- PHONO-MM 20Hz - 20kHz ±0.2dB
- Signal-noise ratio (IHF-A)
- PHONO-MC 80dB (at 250 µ V Input)
- PHONO-MM 90dB (at 5mV Input)
- SUBSONIC FILTER
* High level amplifier section
- Input sensitivity/input impedance
- CD-1, TUNER, AUX-1 and AUX-2 150mV/20k O
- CD-2 (BALANCED) 150mV/2k O
- Installed capacity/rated output
- Total height harmonic wave distortion factor
- CD-1, TUNER, AUX-1 and AUX-2 0.005%/10V (20Hz - 20kHz)
- CD-2 (BALANCED) 0.005%/1V (1kHz)
- Frequency characteristic
- CD-1, TUNER, AUX-1 and AUX-2 1Hz - 100kHz (+0/-3dB)
- CD-2 (BALANCED) 20Hz - 50kHz (+0/-3dB)
- Signal-noise ratio
- Muting
- - XXINF DB (LED blinking indication)
- TONE CONTROL
- BASS ±10dB/100Hz
- TREBLE ±10dB/10kHz
* Synthesis
- Power source electrical outlet
- Power source
- Electric power consumption
- 29W (it depends on electric supplies control method)
- Size
- (W) 476 (H) 144 (D) 388mm (height of the knobs and the foot is included)
- Weight
(1990)
FOR SALE / TRADE 
HOME / master-index 